Solo Single Tank Monitor and Legacy 8 Tank Monitors
None Fouling Sensors for use on the outside of Composite Tanks and None Fouling Rods that go inside of your Metal Tanks
Free Shipping on All US Orders Over $100 & Discounted Shipping to Canada
WE MANUFACTURE ALL OUR OWN PRODUCTS IN THE USA
Manuals & Fliers at Bottom of Page
If you just want to take advantage of all the features of our panel remember our panel
works with just about every sensor on the market today.
WE MANUFACTURE ALL OUR OWN PRODUCTS IN HOUSE
NEW PROVIDENCE MARINE / FERRIELLO SALES LLC
Profile Series 8-Tank Monitor Firmware R3.1a
When you push the up or down arrow you will get the screen below.
Cut out for 6.0: 5.1/4 Wide by 3 1/8 high
Cut out for 7.0: 5 1/4 Wide by 3 1/8 high
Legacy 6.0 & 7.0 Version 2.0
Legacy panels come with panel only, no sensors.
1 Tank Solo Panel No Alert No sensor Kit
Panel size 2.0" H X 3.5" W
Cut out size 1.5" H X 2.5/8" W
1 Tank Solo Panel for Waste tank with Full alert no sensor kit
Panel size 2.0" H X 3.5" W
Cut out size 1.5" H X 2.5/8" W
1 Tank Solo Panel for Fresh Water tank with Empty Alert no sensor kit
Panel size 2.0" H X 3.5" W
Cut out size 1.5" H X 2.5/8" W
Under Counter Mount No sensor kit
Empty or Full Alert
Profile Solo Display Module For Under-Counter Installation
This version of our popular Solo tank monitor and display is functionally identical to
the Solo display panels described above, it is just housed in a sturdy ABS enclosure
for easy under-counter or under-cabinet installation.
Of all our tank monitors and displays, this is by far the easiest to install as there is
no panel cutout to make. To secure it you just need 4 screws.
Additionally, the Empty and Full calibration buttons have been hidden away inside
of this units housing thereby preventing inadvertent re-calibration or re-configuration
by children or curious guests.
Basic Features:
- Runs our simplified EZ-Profile algorithm.
- Monitors one tank.
- Tank level displayed in quarters.
- Optional autonomous tank monitoring.
- Optional tank high/low alert light.
- Compatible with all of our capacitive sensors, most capacitive sensors
- manufactured by other companies, & 240-33 Ohm float sensors.
- Push button empty/full calibration.
- Overall module dimensions: 4 5/16" wide (measured at the flange)
- by 1 5/8" tall by 2 1/2" deep
- Visible face dimensions: 3 1/8" wide by 1 5/8" tall.
PVC Rod for Metal Tanks. View of 1" pipe thread fitting. Bottom end is sealed
or can be shipped open ended and you cut and seal with simple instructions.
Reading is through the PVC pipe. This is a non fouling rod in waste tanks.
To right 5 Hole SAE to 1" flange for our water & waste rods
The flange can be purchased for $19.95 for Straight Rods
Click on link below for Manuals and Fliers
Profile Series 8-Tank Monitor Firmware R3.1a
Legacy 6.0 & 7.0 Cut out Sheet
Solo Manual
Hunter Guide, switch from Ultra 8 to our legacy
Hunter 1999 Legacy Installation
REFUND POLICY
NO REFUNDS ON CUSTOM ORDERS:
i.e. Finished Rods, Custom Panels, Logo's, etc.
20% restocking charge on all returns. Merchandise must be in NEW condition and have not been installed. Must have RA number
Shipping and handling to customer at our cost is also deducted from return even though customer may not have been charged.
Defective Merchandise will be repaired or replaced per Warranty agreement in OWNERS MANUAL.
